Author Topic: VIIC/41 - Schematices drawing  (Read 512156 times)

0 Members and 15 Guests are viewing this topic.

Offline NZSnowman

  • Admiral4
  • *
  • Posts: 2,419
  • Gender: Male
  • U-1308
    • U-1308 - Wikipedia
Re: VIIC/41 - Schematices drawing
« Reply #1050 on: 24 Oct , 2012, 11:12 »
Check out this number  ;D ;D ;D ;D ;D


 
« Last Edit: 24 Oct , 2012, 11:14 by NZSnowman »

Offline tore

  • Tore
  • *
  • Posts: 2,539
  • Gender: Male
Re: VIIC/41 - Schematices drawing
« Reply #1051 on: 24 Oct , 2012, 12:58 »
Check out this number  ;D ;D ;D ;D ;D


 
Coincident ? Very flattered to have your 1308 post on my page! Congrats with your new Avetar very good!
Tore

Offline NZSnowman

  • Admiral4
  • *
  • Posts: 2,419
  • Gender: Male
  • U-1308
    • U-1308 - Wikipedia
Re: VIIC/41 - Schematices drawing
« Reply #1052 on: 25 Oct , 2012, 13:06 »
Updated the drainage pipe in the aft engine room - corrected the size of the pipe and layout.

(OLD)


(NEW)

Offline NZSnowman

  • Admiral4
  • *
  • Posts: 2,419
  • Gender: Male
  • U-1308
    • U-1308 - Wikipedia
Re: VIIC/41 - Schematices drawing
« Reply #1053 on: 25 Oct , 2012, 14:37 »

Fig. 1. Main Engine frame added.

TopherVIIC

  • Guest
Re: VIIC/41 - Schematices drawing
« Reply #1054 on: 26 Oct , 2012, 04:59 »
NZ... your drawings are better and better. Good job! You obviously can visualize even the most intricate details!
Christopher...

Offline NZSnowman

  • Admiral4
  • *
  • Posts: 2,419
  • Gender: Male
  • U-1308
    • U-1308 - Wikipedia
Re: VIIC/41 - Schematices drawing
« Reply #1055 on: 30 Oct , 2012, 20:16 »
Simon.
Thought you was satisfied with snow for this year, we had our first snowfall for the season this morning, even way down in the lowland. I have to brace for the winter putting on the wintertyres with studs. Looking forward to se your drawing of the engine topview it`s a lot of stuff cramped on to the cylindercover. 
Tore

Hi Tore

This was what I was doing yesterday. I was mapping this avalanche event.

The avalanche was just under 45,000 m

Offline tore

  • Tore
  • *
  • Posts: 2,539
  • Gender: Male
Re: VIIC/41 - Schematices drawing
« Reply #1056 on: 31 Oct , 2012, 00:09 »
Don`t export it northwards here we have sufficient already, this morning it is snowing so we produce plenty of our own.
Tore.

Offline NZSnowman

  • Admiral4
  • *
  • Posts: 2,419
  • Gender: Male
  • U-1308
    • U-1308 - Wikipedia
Re: VIIC/41 - Schematices drawing
« Reply #1057 on: 31 Oct , 2012, 16:31 »
Here a 3D view (from same web site as Maciek share with as yesterday) which is only 2 km away from where I live :D

http://www.360cities.net/image/limestone-castle-hill/?from=map,-43.23232,171.72515,15#18.01,41.18,108.3

Offline Rokket

  • Administrator
  • *
  • Posts: 2,362
  • Gender: Male
  • Submarine Enthusiast
    • AMP - Accurate Model Parts
Re: VIIC/41 - Schematices drawing
« Reply #1058 on: 10 Nov , 2012, 00:51 »
Wow, LOVE the new banner
AMP - Accurate Model Parts - http://amp.rokket.biz

Offline NZSnowman

  • Admiral4
  • *
  • Posts: 2,419
  • Gender: Male
  • U-1308
    • U-1308 - Wikipedia
Re: VIIC/41 - Schematices drawing
« Reply #1059 on: 04 Dec , 2012, 11:32 »


The thick pipe marked with letter C I believe is a sounding pipe as marjked here:



(source: http://uboatarchive.net/U-570Plate8A.htm)

The thinner pipe marked with letter D is hard to figure out.
I think it can be water compensating line:


(source: http://uboatarchive.net/U-570Plate10T.jpg

But according to the "FUEL OIL STOWAGE AND EQUIPMENT" chapter in the type IXC study (http://uboatarchive.net/DesignStudiesTypeIXC.htm):
Quote
The compensating lines to the individual fuel ballast tanks run directly to the bottom of the tank while the line for the outboard normal fuel tanks leads into the small salt water niche (1.5% of fuel tank's volume) in the bottom of the tank; a line then leads from the top of the niche to the bottom of the fuel tank.

it looks as it is located to high.

It can be also exhaust gas blowing line:


(source: http://uboatarchive.net/U-570Plate16.htm

but it in the turn looks located to low.

--
Regards
Maciek

Maciek, Do you think that pipe "D" could be the exhaust gas blowing pipe?

If the Seawater compensating pipes are 60 mm and the exhaust gas blowing pipes are about 75 mm. Pipe "D" looks closer to the 75 mm ???

Offline Greif

  • Admiral2
  • *
  • Posts: 755
  • Gender: Male
Re: VIIC/41 - Schematices drawing
« Reply #1060 on: 06 Dec , 2012, 07:44 »
Simon, your work continues to impress, beautiful and well executed as always my friend.  The avalanche looks pretty sobering that is for sure.
 
Ernest

Offline NZSnowman

  • Admiral4
  • *
  • Posts: 2,419
  • Gender: Male
  • U-1308
    • U-1308 - Wikipedia
Re: VIIC/41 - Schematices drawing
« Reply #1061 on: 13 Dec , 2012, 12:09 »
Update for the Free-Flooding Vent patterns

► Made a few changes to the vents base on the better photographs of U-1105. (Top - Type VIIC/41's with the Alberich coating/Lower layer is the vent patterns for Type VIIC/41's).

Stern Vents


Bow Vents


It has been always documented that U-1306 had an Alberich coating. This morning I found photograph evidence of this. If you look hard at the Free-Flooding Vent on the deck casting (lower left of the photo) you can make out the shape of the vents and how it matches of the other Alberich boats :)


Fig. 1. U-1306. http://www.subsim.com/radioroom/showthread.php?t=149950&page=22

TopherVIIC

  • Guest
Re: VIIC/41 - Schematices drawing
« Reply #1062 on: 13 Dec , 2012, 12:26 »
Quote
It has been always documented that U-1306 had an Alberich coating. This morning I found photograph evidence of this. If you look hard at the Free-Flooding Vent on the deck casting (lower left of the photo) you can make out the shape of the vents and how it matches of the other Alberich boats 
Nice catch Simon!

Offline NZSnowman

  • Admiral4
  • *
  • Posts: 2,419
  • Gender: Male
  • U-1308
    • U-1308 - Wikipedia
Re: VIIC/41 - Schematices drawing
« Reply #1063 on: 13 Dec , 2012, 15:02 »
Hi All

I am looking for help. I am trying to draw the wooden decking outline. I have never seen any German measurement for the decking so I have to do this by line-of-sight. There are two things I need to get correct the deck outline and the deck casting outline. The problem is that the angle between the deck outline and the deck casting outline changes, at the bow and stern it look 70-80

Offline tore

  • Tore
  • *
  • Posts: 2,539
  • Gender: Male
Re: VIIC/41 - Schematices drawing
« Reply #1064 on: 14 Dec , 2012, 00:08 »
Simon.
I have no means to measure the angles, but am wondering about your blue casingdeck image. I the way of the lower wintergarden I guess the casing deck has a small 2nd. widening between frame 41+ and 47. See picture below. I have some photos showing KNM the decking in the vicinity of the snortmast see below, on the Kaura decking we did away with the wintergarden and the 2nd deckwidening.